The Suzuki K6A engine is a legendary 660cc three-cylinder powerhouse, famous for its role in Japan’s "Kei car" culture. Whether you are swapping a K6A into a custom buggy, reviving a Suzuki Jimny, or troubleshooting a Carry truck, having a is the difference between a smooth-running engine and a fried wiring harness .
| Pin | Signal Name | I/O | Type | Notes | |-----|---------------------------|------|---------------|--------------------------------| | B1 | +12V Ignition switched | Power| | From ignition switch (IG1) | | B2 | Backup power (constant) | Power| +12V | To keep fault codes, adaptive | | B3 | Engine ground | GND | Power | To chassis/engine | | B4 | Vehicle speed sensor (VSS)| In | Open collector| 4 pulses/rev from speedo | | B5 | Coolant temp sensor (ECT) | In | Analog (NTC) | 0-5V, ~2.5kΩ @20°C | | B6 | Intake air temp (IAT) | In | Analog (NTC) | Inside MAF sensor | | B7 | Throttle position (TPS) | In | Analog 0-5V | Idle ~0.5V, WOT ~4.5V | | B8 | Manifold absolute pressure| In | Analog 0-5V | MAP sensor (NA only) | | B9 | MAF sensor signal | In | Analog 0-5V | Frequency type on some models | | B10 | Oxygen sensor (front) | In | 0-1V (narrow)| Zirconia | | B11 | Oxygen sensor (rear) | In | 0-1V | Catalyst monitor | | B12 | Knock sensor | In | AC signal | 5-15kHz resonant | | B13 | A/C switch input | In | +12V | Request from HVAC | | B14 | Power steering pressure | In | Switch | Idle-up request | | B15 | Brake switch | In | +12V | For torque reduction | | B16 | Clutch switch (MT) / PNP | In | GND or +12V | Park/Neutral (AT) | | B17 | Starter signal (ST) | In | +12V | During cranking | | B18 | Ignition feedback (IGF) | In | 0-5V | From igniter (confirm spark) | | B19 | Diagnostic request (K-Line)| I/O | 12V serial | ISO 9141-2 (OBD) | | B20 | Check connector (test mode)| In | GND or float | Factory diagnosis | | B21 | Immobilizer signal (if) | I/O | Serial | To key transponder amp | | B22 | Alternator FR signal | In | PWM | Field regulation monitor | | B23 | Alternator C terminal | Out | PWM | Generator control | | B24 | Engine speed output | Out | Square wave | To instrument cluster (4/cyl) | | B25 | +5V sensor reference 2 | Out | +5V | For MAP, ECT, IAT | | B26 | Sensor ground 2 | GND | Analog | Separate return path | | B27 | +5V sensor reference 3 | Out | +5V | For knock sensor bias | | B28 | Injector monitor (INJ MON)| Out | Logic | Scope use only | | B29 | Data link (CAN-L) | I/O | 2.5V diff | On late K6A (2005+) | | B30 | Data link (CAN-H) | I/O | 2.5V diff | | | B31 | Spare / NC | – | – | | | B32 | Spare / NC | – | – | | suzuki k6a engine ecu pinout high quality
Alex had always been passionate about cars. As a teenager, he spent hours in his father's garage, learning the ins and outs of engine repair and modification. Years later, as a skilled mechanic, he owned a small workshop where he helped car enthusiasts tune and upgrade their vehicles. high-quality ECU pinout The Suzuki K6A engine is
The breakthrough came when Alex discovered a small, dedicated community of Suzuki enthusiasts who shared his passion for engine tuning. They provided him with valuable insights, shared their own documentation, and offered guidance when he encountered roadblocks. Connector B : 21-40 pins | Pin |
Useful for cross-referencing sensor locations with ECU pinouts.